W-701 Range

WASP W7xx fuel filter/water separator rangeWASP Fuel Filters offer a new cost effective range of primary filtration equipment for marine, heating, industrial and transport applications. The problems that can occur due to water and sediment in fuel are well known and WASP Filters offer a wide choice of options to cover most requirements.
Metal bowl units meet and exceed the requirements of ISO 10088 Annex B.

 

Overview 

WASP Fuel Filters offer a new cost effective range of primary filtration equipment for Marine, Industrial and Transport applications.

The problems that can occur due to water and sediment in fuel are well known and WASP Filters offer a wide choice of options to cover most requirements.

Flow rates range from 1 - 20,000 liters per hour and port sizes are from 1/4'' BSP to 2'' BSP. A DN 50 flanged version is available on the 2'' ported model. All models have a maximum working pressure of 4 bar. 

These WASP strainers are fitted with a well constructed 'washable' stainless steel element that will give many years of effective service. Micron ratings available are 60, 100 and 300 with 400 micron offered on the 2'' models.

Pre-cleaning liquids by passing it through a washable strainer will assist in reducing costs down stream. The only consumable item in the WASP Liquid Strainers is a seal kit.

Features

  • Up to 20,000 litres per hour flow rate
  • 1/2'' to 1'' BSP connections
  • Inexpensive solution
  • Choice of separators, paper elements or long life stainless steel
  • LM6 grade aluminium filter heads with reversible stainless steel bracket & bolts
  • Powder coated aluminium filter heads for corrosion prevention & long service life
  • 60 & 300 micron stainless steel washable elements

How does it work?

 1. Separation:  

The incoming flow of fuel oil changes velocity and direction, reducing the possibility of further reduction of any water droplets present through impact. 

2.  Coalescence:   

This takes place on and just below the flow dispersion member allowing the separated water to descend to the bottom of the filter bowl. 

3. Filtration:   

The fuel finally passes through the stainless steel filter element. This removes all particulate above 100 micron still suspended in the fuel after the separation process.

 

Product Range

 

W-701 range Filtration (micron) Details
W-70107/006 60mic stainless steel 1/2” Ports, Metal bowl
W-70107/01 100mic stainless steel
W-70107/03 300mic galvanised steel
W-70104/006 60mic stainless steel 3/4” Ports, Metal bowl
W-70104/01 100mic stainless steel
W-70104/03 300mic galvanised steel
W-70101/006 60mic stainless steel 1” Ports, Metal Bowl
W-70101/01 100mic stainless steel
W-70101/03 300mic galvanised steel

 

Spares and options

W-FS13 W-701 range mounting bracket
W-60100/006 Replacement 60 mic pleated stainless steel element
W-60100/01 Replacement 100 mic pleated stainless steel element
W-60100/03 Replacement 300 mic pleated galvanised steel element
W-3207 Gasket kit
W-3207V Viton gasket kit

 Model 70107 can be fitted with a magnetic column to remove ferrous particles. 

 

Install/Maintenance

Installation

The flow direction is indicated by arrows and must be observed. The filters can be installed in any position, however, we recommend that filter units are mounted vertically with the cover uppermost. This will assist the separation and collection of any water and particulate into the bottom of the housing ready for drain off (water separation of diesel fuel will only take place at lower flow rates).

 

Servicing

Due to the simple and effective construction very little maintenance is required other than draining off any impurities, and the periodic removal of the washable element for cleaning. 

Cleaning the filter is carried out by unscrewing the central bolt and then unscrewing the bowl. Carefully wash the filtering element with clean diesel, gas-oil or gasoline. Remount the unit and check that the seals are integral and well placed. Paper elements should be replaced as they cannot be reused (see above spares). Water can be drained by opening the bleed screw on the lid and then the water drain at the bottom of the bowl.

See the Servicing and support section

Technical  Spec

WASP W701xx Specifications

 MODEL
FLOW RATE (litres / hour)
ELEMENT
PORT SIZE
DIMENSIONS (mm)
 W70107/006
1000 - 2000
60 mic ss
½" BSP
120 x 181
 W70107/01
1000 - 2000
100 mic ss
½" BSP
120 x 181
 W70107/03
1000 - 2000
300 mic gs
½" BSP
120 x 181
 W70101/006
2000 - 3000
60 mic ss
1" BSP
120 x 181
 W70101/01
2000 - 3000
l00 mic ss
1" BSP
120 x 181
 W70101/03
2000 - 3000
300 mic gs
1" BSP
120 x 181

Notes:
Flow rates are approximate
ss = stainless steel  gs = galvanised steel  F = flanged connections
Aluminium filter body and cover- maximum working pressure 4 bar - maximum operating temperature 90°C

Maximum operating pressure           2bar
Max operating temp (metal bowl)   90 deg C
Compatible with diesel and heavy oil

 

w 701 dimensions 

Need help selecting a filter?

See our guide to help you select the most suitable filter for your needs.

Technical Support

How it works

See how the Separ filter works to separate water and particulate from fuel. 

SWK2000 flow diagram transparancy

How to Order

Call or email us to place your order. We accept ALL major credit and debit cards, bank transfer and also PayPal. 

Contact Us TabPhone copy



 

Expert advice

Unsure which spare parts you require? Or if a Separ filter will meet your requirements? 

Talk to our expert team. Call 01923 276 007

swk200010trans

 

Delivery options

We have a wide range of shipping options available to suit your destination and budget.

 

 

Wooden-Crate-psd42799 copy

Contact Us

3 Kingley Park, Station Road, Kings Langley, Herts, WD4 8GW

Tel: +44 (0)1923 276007

Fax: +44 (0)1923 267463

Email: This email address is being protected from spambots. You need JavaScript enabled to view it.

Follow Us

32x32-Circle-55-TW  Twitter
32x32-Circle-55-FB  Facebook
32x32-Circle-55-YT  YouTube